La versione beta della nuova release del firmware per la RED one diventa "silenziosamente" ufficiale. E come sempre è scarcabile dal supporto RED.
Questi tutti i dettagli:
Significant changes since beta Build 17 v.3.3.9
- Completed optimization for RED 16GB CF cards.
- Addition of embedded time code in HD-SDI outputs.
- Addition of CROSS JAM (creation of 23.98 fps from 29.97 timecode)
- Addition of CROSS GEN (creation of 29.97 fps from 23.98 timecode)
- Added USER KEY function – Record
- Changed method of writing camera LOG file – access via SETUP menu.
- Changed location of PRE-RECORD – access via MEDIA menu.
- Selection of lens Distance data reporting in Feet or Meters
- Addition of Audio LINE input gain control 0dB / 10 dB.
- FALSE COLOR exposure meter tracks VIEW selection – REC709 / REDspace
- Corrected operation of Shutter PHASE control.
- Added USER programmable Safe Action / Title guides.
- Changed MAGNIFY to display 1:1 native sensor resolution.
- Added selection to playback clips using CLIP or CAMERA LOOK values.
- Added USER PREFERENCE file.
Significant changes since Build 16.
- Addition of RAW exposure meter.
- Addition of 4K HD recording mode (3840×2160 pixels).
- Support for RED 16GB CF cards and RED-RAM 64GB flash drive.
- Addition of MAX checkbox to CONFIGURE / NEW PROJECT menu.
- Note: Enable MAX for maximum image quality, disable MAX for faster decode times for 4K footage.
- Added Timecode Output enable checkbox: enables Time Code on LEMO 5-pin connector.
- Addition of embedded time code in HD-SDI outputs.
- Addition of embedded audio in HD-SDI outputs.
- Addition of CROSS JAM (creation of 23.98 fps from 29.97 timecode)
- Addition of CROSS GEN (creation of 29.97 fps from 23.98 timecode)
- Improved JAM SYNC operation: removed requirement to record before syncing.
- Genlock (Tri-Level Sync) available when operating with OPEN GATE.
- Change of name for Sensitivity parameter – ASA (now ISO).
- USER KEY MODE “VIEW RAW” now toggles between VIEW RAW and selected VIEW menu selection.
- Change of name for GPI and USER KEY parameter – BURST -> TIMELAPSE.
- Added USER 5 Key (located on RED-LCD).
- Added GPI trigger functions – Pre-Record, Shut Down, Play Clip, Next Clip.
- Added USER KEY functions – Ramp, Timelapse, Record
- Added CLEAR LOOK function.
- Added ability to disable GUI elements – EVF menus and Grey Scale defaulted OFF.
- Added ability to defeat EVF menu controls when EVF menu display is set to OFF.
- Changed method of writing camera LOG file – access via SETUP menu.
- Changed location of PRE-RECORD – access via MEDIA menu.
- Added warning screen to advise if media is removed without first Unmounting.
- Non-speed verified CF cards now permitted to record at 2K RAW resolution.
- Note: Non-speed verified CF cards is solely at end-user risk.
- Note: RED makes no representations regarding maximum frame rate or immunity to dropped frames.
- Resolved RED-LCD sometimes tearing in lower 10% of screen with 4K footage.
- Re-sized system error messages from full screen to upper central area of GUI.
- Added flashing “RECORD dot” within GUI to indicate system error.
- Corrected spelling errors in drive format splash screens.
- Resolved intermittent “stuck in POST record” error.
- Resolved 29.97 fps Time Base QuickTime reference file issue with long record times.
- S4/i Lens Data Interface (requires corresponding Lens Interface hardware).
- Allow lens Distance data reporting in Feet or Meters.
- Revised audio PPM metering (requires corresponding Revision 2 audio board).
- Addition of Audio LINE input gain control 0dB / 10 dB.
- FALSE COLOR exposure meter tracks VIEW selection – REC709 / REDspace.
- Added user programmable Safe Action / Title guides.
- Changed MAGNIFY to display 1:1 native sensor resolution.
- Added selection to playback clips using CLIP or CAMERA LOOK values.
- Added USER PREFERENCE file.
- Added Battery Cycle count to camera firmware status panel.
- Corrected operation of Shutter PHASE control.
- Corrected Audio Codec error on clip playback
- Corrected Audio Level adjustment from User Keys.
Operational restrictions of Build 17 series firmware.
- S4/i Lens Data Interface requires corresponding Lens Interface hardware.
- Revised audio PPM metering requires corresponding Revision 2 audio board.
- Non-speed verified CF cards are limited to 2K record resolution.
- Non Build 17 formatted media may report as “INCOMPATIBLE”- reformat to clear.
- Image Magnify is not available during recording at 3K and 4K resolutions.
- Entering and exiting Image Magnify causes a visual disturbance to monitor outputs.
- Time Code / Edge Code values displayed in monitor outputs do not update in real-time.
- 1080p HD-SDI outputs do not support PsF signal formatting option.
- COLOR exposure meter display is inaccurate if VIEW is set to RAW.
- Limited GUI on HD Preview when both RED-EVF and RED-LCD are selected.
- EVF display with blank for approximately 3 seconds when in SYNC refresh mode:
- when exiting OPEN GATE mode
- after a change in Project Resolution
- after exiting MAGNIFY when in 4K resolution
- after a Varispeed frame rate change
- Cannot import camera LOOK (.RLK) files from RED Alert! or REDCINE.
Copyright© 2008 RED Digital Cinema, All Rights Reserved.
Nessun commento:
Posta un commento